Chapter 05
Instruments and Tools
(ENGRAVING DEVICES)
Scribe, etched
Order
No. 05-068
for clamping in to the knife holder (order no. 05-043).
Scriber, etched, left-handed angle, Order
No. 05-068A
Scriber, etched, right-handed angle, Order
No. 05-068B
This is a scribing tool that scribes lines with one vertical wall and
one angled wall. The angled wall is on the let or right side of the
scribed line.The blades can scribe angled lines with the following angles:
30 degrees, 45 degrees, 60 degrees and 75 degrees. These can be used to
simulate louvres, armour plate edges, joint lines, control surfaces, lapped
joints, etc.. The back of each holder can also be used as a scribing saw.
0000
Double Scriber, etched, parallel Order
No. 05-068C
This is a scribing tool that scribes two parallel lines in one stroke.
The set includes 4 complete scribers (4 blades and 4 holders).
The blades can scribe parallel lines with the following distance between
lines: 0.33mm (~0.01 in) , 0.5mm (~0.02 in), 0.75mm (~0.03 in) and 1mm.(0.04
in). The back of each holder can also be used as a scribing saw.
Double Scriber, etched, parallel, wide Order
No. 05-068D
for parallel lines 1.25mm (~0.05 in) , 1.5mm (~0.06 in), 1.75mm (~0.07
in) and 2 mm.(~0.08 in).
| Order No. 05-068 |
€ 6,90
|
| Order No. 05-068A |
€ 8,90
|
| Order No. 05-068B |
€ 8,90
|
| Order No. 05-068C |
€ 8,90
|
| Order No. 05-068D |
€ 8,90
|
Engraving Device 4
this stainless steel scriper with fine,
rounded point is suited for creating the finest engravings.
| Order No. 05-155 |
€ 8,90
|
Engraving-Needle Holder with Needle
For engraving the finest surfaces. Span 0-1 mm. Also suited for drills.
With specially hardened engraving needle. Length 7,5 cm
| Order No. 05-058 |
€ 7,60
|
Engraving Needles
Spare needles for 05-058. Finest workmanship, specially hardened. 2
pcs.
| Order No. 05-057 |
€ 1,50
|
Engraving Tape, self-adhesive
als Führungslineal auf dem Modell aufkleben und z. B. mit
Gravurinstrument
4 entlang ritzen. Um Radien zu gravieren, das Band von einer Seite V-förmig
einschneiden.
| Order No. 05-050 |
|
€ 4,20
|
Engraving Insert - three-edged
Ø 2,0 mm, made of special steel, three-edged
cut. For inserting in holders 05-119 or 05-013.
| Order No. 05-160 |
€ 1,95
|
Engraving Device 1
Spicular, for drawing thin engravings.
| Order No. 05-014 |
€ 6,50
|
Engraving Device 2
Lanceolately bent, for creating V-shaped engravings.
| Order No. 05-015 |
€ 6,50
|
Engraving Device 3
For smoothing the surface after engraving and for clean draw-off of
raised engravings.
NEW at the same price: double-ended with contrary bend.
| Order No. 05-016 |
€ 6,50
|
a special knife for scribing plastics. A plate can be scored several times and then severed cleanly along the parting line. Also an insiders' tip for drawing straight engravings. Very similar to the Tamiya Scriber.
| Order No. 05-121 |
€ 10,90
|
Set of Modelling and Engraving Devices
Consisting of wax modelling tool Hylin, engraving devices 1 and 3.
Especially well-priced set.
| Order No. 05-017 |
€ 15,60
|
Page 27
 |
|
 |
|
|
