Chapter 05
Instruments and Tools
(CUTTING MATS + AUXILIARY TOOLS)
JH Montagehalterungen:
Modeler stands for
monoplanes, plywood, 1/72
laser cut quick fixed kit. All included, but a screwdriver and glue.
Very helpful to fix the wing on your model airplane.
| Order No. 05-019 |
€ 18,90
|
Modeler stands for biplanes,
plywood, 1/72
siehe oben
| Order No. 05-019A |
€ 19,95
|
Modeler stands for
monoplanes, plywood, 1/48
siehe oben
| Order No. 05-019B |
€ 23,90
|
Modeler stands for biplanes,
plywood, 1/48
as above
| Best. Nr. 05-019C |
€ 24,90
|
Wing Fixing Jig
make it easy to assembly the wings to a mono- or a biplane. Variable
width of the Wing Fixing Jig from 8,5 cm – 15,5 cm, high 9 cm.
| Order No. 05-012 |
€ 34,95
|
Superglue Applicator Set
Small, fork-shaped instrument and a needle instrument
for precisely placing superglue drops.
Picture TWN
| Order No. 05-142 |
€ 11,50
|
Touch-n-Flow, Solvent Applicator by Flexi
File
Thin glass tube with canula. For gathering thin-fluid
solvents (e.g. Micro Weld or Tamiya Adhesive extra thin) by capillary attraction
and precisely positioning them.
Picture
TWN
| Order No. 05-143 |
€ 11,90
|
Cutting Mat 300 x 450 mm
Cutting mat in three-layered design. Transparent and with lattice,
allowing for cutting to a pattern, placed underneath the cutting mat. Spares
your knife and your work table.
| Order No. 05-047 |
€ 14,50
|
Cutting Mat 220 x 300mm
See above, but non-transparent green.
| Order No. 05-053 |
€ 7,40
|
Cutting Set
Simple and ingenious tool for the modeller. Consisting
of two black plexiglass plates as well as a transparent holding die for
etched parts. The die enables you to securely hold the parts to be cut.
Due to the black colour even smallest parts placed on the plates can easily
be recovered. NEW: Size of each plate: 18,0 cm x 11,0 cm
| Order No. 05-125 |
€ 21,50
|
Rivet-, Screw- and Nut-Sets
Different rivets, screw heads and nuts with plastic
stud bolt, corresponding HSS-drill and etched drill pattern. Very nice
design by CMK.
| Order No. 06-10001 | Button-head rivet-set 1.2 mm |
|
€ 7,90
|
| Order No. 06-10002 | Button-head rivet-set 1.0 mm |
|
€ 7,90
|
| Order No. 06-10003 | Button-head rivet-set 0.8 mm |
|
€ 7,90
|
| Order No. 06-10004 | Hexagonal screw head set 2.0 mm |
|
€ 7,90
|
| Order No. 06-10005 | Hexagonal screw head set 1.5 mm |
|
€ 7,90
|
| Order No. 06-10006 | Hexagonal nut set with stud bolt 2.0 mm |
|
€ 7,90
|
| Order No. 06-10007 | Hexagonal nut set with stuc bolt 1.5 mm |
|
€ 7,90
|
Contour Gauge
For gauging and transferring contours. You may e.g. take the
contour of a fuselage and transfer it to a plastic plate for a frame.
Due to the large number of small metal rods even quite complex
forms may be transferred. 14 cm x 8.5 cm
| Order No. 05-070 |
€ 13,50
|
Metal Mixing Spatula
With this mixing spatula you can effortlessly mix colours, silicon
and casting resin.
Due to its polished surface the spatula is easily cleaned with a cloth
and therefore usable again within seconds.
| Order No. 04-052 |
€ 4,50
|
Spatula - small
Well suited for applying putty, with two differently shaped ends.
| Order No. 05-087 |
€ 4,90
|
Probe 1
For placing drops of glue at inaccessible places etc., universally
applicable.
| Order No. 05-018 |
€ 4,50
|
NEW Probe 2
Double-sided, for placing drops of glue at inaccessible places, holding
small parts etc., universally applicable.
| Order No. 05-018A |
€ 5,50
|
Metal Angle 90 Degrees
Best quality for scribing and marking, with cm and inch scaling. Size:
5 cm x 4 cm.
| Order No. 05-135 |
€ 13,90
|
Page 33
 |
|
 |
|
|
